Atrius Super Selektor Compatibility & Install Guide

Atrius Super Selektor Compatibility & Install Guide

One Horse Express rifle with Atrius Forced Reset Selector

Forced Reset Selector guide · Atrius

Made in the U.S.A.

Atrius Super Selektor Compatibility & Install Guide

What your AR-15 needs to run the Atrius Forced Reset Selector, how installation works, and the safety checks to do first.

Quick answer

The Atrius Super Selektor (Atrius FRS) needs a mil-spec AR-15 lower with a low shelf or full-profile trigger pocket, a full-profile bolt carrier group, an H2 or H3 buffer, and a trigger from the Atrius compatibility list. It replaces the safety selector, not the trigger group. Always confirm your parts on the Atrius compatibility page before you buy or install. New to the part? Start at our Atrius Super Selektor hub.

Compatibility

What your AR-15 needs

PartAtrius requirementAt One Horse
Lower receiverMil-spec AR-15 lower with a low shelf or full-profile trigger pocket. High shelf lowers are not compatible.Both One Horse lowers are low shelf
Bolt carrier groupFull-profile BCGM16 bolt carrier groups
BufferH2 or H3H2 and H3 buffers
TriggerA model on the Atrius compatibility list, with a flat, uncut, full-dimension trigger barCheck the Atrius list for your trigger

Watch for: Atrius says the selector will not work in AR-10 (LR-308) / SR-25 platforms without significant gunsmithing, AR-9 variants may need professional gunsmithing, and rifles modified to “super safety” specifications may not be compatible. Requirements from the Atrius compatibility page as of November 2026.

Installation

How installation works (overview)

This is a general overview of the Atrius published steps, not a replacement for the instructions in the box. Follow the Atrius user manual, and if you are not sure, have a qualified gunsmith do it.

  1. Make sure the firearm is unloaded: remove the magazine and confirm the chamber is empty.
  2. Remove the pistol grip, then the selector spring and detent.
  3. Remove the original safety selector.
  4. Insert the Atrius detent shaft from the right side of the receiver, about halfway.
  5. Install the spring and cam lever, then push the detent shaft the rest of the way through. Make sure both sides are aligned in the same position.
  6. Secure the left-side lever with its T10 screw. Atrius recommends 15 in-lb with blue thread locker only.
  7. Reinstall the safety detent, spring and pistol grip.
  8. Do a full function check before you load the firearm.

Safety

Function check and safe use

  • Do every check with the firearm unloaded and no ammunition in the area.
  • Atrius describes a check with the upper off, then a function check with the upper on: SAFE should not fire, SEMI should reset normally, and Super Semi should reset as the carrier cycles.
  • If anything binds or does not reset, stop and recheck your lower, bolt carrier, buffer and trigger against the compatibility list.
  • Get comfortable with the rifle in SEMI before using Super Semi, and follow your range rules.

Want it done for you? Every One Horse Express ships with the Atrius FRS installed, timed and test-fired in Brownstown, Indiana. Or buy the selector alone: Ambidextrous or Single Side. See also Forced Reset Technology explained.

FAQ

Common questions

What lower do I need for the Atrius Super Selektor?

Atrius requires a mil-spec AR-15 lower with a low shelf or full-profile trigger pocket. Atrius says high shelf lowers are not compatible. Both One Horse lowers are low shelf.

What bolt carrier and buffer does it need?

Atrius lists a full-profile bolt carrier group and an H2 or H3 buffer as minimum requirements. If you see light strikes, Atrius suggests checking that you are running an H2 or H3 buffer.

Which triggers work with it?

Use a trigger from the Atrius compatibility list. Atrius says the trigger bar should be flat and uncut, full dimension. Check the list for your exact trigger model before you install.

Does it work in an AR-10 or AR-9?

Atrius says the selector will not work in AR-10 (LR-308) or SR-25 platforms without significant gunsmithing, and that AR-9 variants may need professional gunsmithing.

Should a gunsmith install it?

Atrius recommends that modifications be performed by a qualified gunsmith. If you are not comfortable with AR-15 lower work, have a gunsmith or your FFL dealer install it.

Can I skip the install?

Yes. Every One Horse Express ships with the Atrius FRS installed, timed and test-fired, and Forced Reset Ready™ builds are set up for forced reset use.

Check your federal, state and local laws, and ask your FFL dealer, before you buy.

Questions? Email customerservice@theonehorse.com.

Like this? Get the next one by email.News, new builds and deals from One Horse.

Join Our One Horse Waitlist We will inform you when your One Horse product is back in stock!